Because an invisible signature sits inside the print, the print method, the substrate and the print tolerances all directly affect whether it reads. Sending your printer the signed file is therefore not enough. The specification has to state how the file is protected, which tolerances apply, how the trial run is accepted and which changes require a new test.
We described how the signature enters production in how to add protection without touching your packaging. This post sticks to the clauses to put in writing with your printer. The checks below are general headings; the actual values come from a trial run on your own product.
What should you watch for in each print method?
| Print method | Source of variation | What to check in the trial run |
|---|---|---|
| Offset | Ink and water balance, misregistration, density drift across the run | Scans on samples from the start, middle and end of the run |
| Flexo | Flexible plates, relatively high dot gain, anilox and plate wear | Comparison of samples from a new plate and the end of a long run |
| Gravure | Cylinder engraving, cell structure, white backing on film | Repeat scans when a cylinder is renewed, and checks on backing differences |
| Digital | No plate, device-specific screening and colour management | Samples on the same device and settings, and a new test if the device changes |
The method is not the only factor. Board or film, varnish, lamination and foil all change how the surface looks to a camera, so scanning has to be done on the finished pack.
Which clauses belong in the specification?
- File and version. State the design code and version of the approved signed file. Prepress operations such as resampling, colour conversion, trapping or screening changes require written approval, including corrections that look visually trivial.
- Print parameters. Record colour targets, density and registration tolerances, colour sequence and screening. The ISO 12647 series can provide a general framework: ISO 12647-2 includes offset printing on cardboard for packaging, and ISO 12647-6:2020 covers flexo including labels, boxes and flexible packages. Name the edition you are working to.
- Signature-specific tolerance. Conforming to a standard is not enough on its own. The limits accepted for scanning are set in the trial run and added to the printer's quality control checklist.
- Materials and inks. Name the board or film, ink series, varnish and lamination. If "or equivalent" is allowed, make testing a precondition.
- Plates and cylinders. State when they are renewed and what check follows renewal.
- Proof and trial run. A proof may be good enough for colour approval, but the scanning test belongs on the real substrate in a run close to production conditions.
- In-run sampling. State how often samples are taken, from which reel or pallet, and how scan records are kept.
- Deviation and decision. Say who stops the press when scanning drops, how the batch is segregated and who makes the call.
- Change notification. Require advance notice of any change of press, line, material, ink or printer, and rule out subcontracting.
- Confidentiality and counting. Define who can access the signed file and how surplus is counted and destroyed. For high-risk work, ISO 14298:2021, which sets management system requirements for security printers, can serve as a reference. We list the counting clauses in copied packaging or printer overrun.
How do you run acceptance on a trial print?
The point of a trial is not to see the file scan once but to find the acceptable range. This sequence works:
- Keep production conditions. Use the same press, substrate, ink and finishing, with no special settings for the trial.
- Scan the finished form. Read cut, folded and laminated packs rather than flat sheets.
- Add field conditions. Try different phone models, lighting and angles in something close to a retail environment, and check the effect of wear and reflections.
- Measure the variation. Scan the start, middle and end of the run, plus the lightest and darkest acceptable prints.
- Keep the reference. Archive approved samples, print parameters and scan results under the version number, so later runs can be compared with them.
How should responsibility be divided?
The most common dispute is that nobody wrote down who answers when scanning drops. ISO 12647-6:2020 deals with assigning responsibility and recommending tolerances for critical process parameters, and the same approach works for the signature. One practical split:
| Issue | Printer | Brand and signature side |
|---|---|---|
| Holding print parameters | Responsible | Provides targets |
| Using the signed file unchanged | Responsible | Approves the version |
| Setting tolerance and acceptance limits | Advises | Responsible |
| In-run scan records | Sets samples aside or scans them | Evaluates results |
| Batch decision on deviation | Reports | Decides |
When is a new test needed?
Scanning is repeated on samples when the printer, the material or the ink supplier changes, and when a new pack size or design joins the product family. Add plate or cylinder renewal and any change of press to that list. Skip this check and the problem surfaces on the day the signature fails to read in the field.
Where does Grafex come in?
With Grafex, suitability is assessed during needs analysis from the print file and a sample pack. The signature is placed in the design in a way suited to the print method and material, a proof and verification test are carried out before printing, and the pack is then printed on the existing line. In the management panel, designs are tracked by version and print method. The stages are on the solutions page.


